Sprinkler head adjustment may be required in the event of a water shortage. By adjusting the heads of their sprinkler system, homeowners can stop wasting water and at the same time, more efficiently water their lawn and landscaping area. Note that adjustment is not necessarily the same thing as repair. When you adjust sprinkler heads, you are altering the regular course of the sprinklers. To start with, determine the coverage that the sprinkler heads get at ordinary water pressure.
If you want more power, then you could open up the water line full throttle which will give you the highest water pressure. This can result in over-watering, however, not to mention an absence of water in other areas. Understand that sprinkler heads are created to spray in a particular pattern. Traditionally, homeowners install forty-five degree heads near the corners, fifty-degree heads on the lengths, and three hundred and sixty-degree heads in the center. When they spray in combination it produces a perfect “arching” effect. Regardless of adjustment, it is important these patterns meet each other right at the edge, but not overlap. Why? Because overlapping causes over-watering.
How can you see to proper sprinkler head adjustment? Your first option would be to adjust water pressure from the water source. You could choose to expand the range or alter the length of the spray. You could adjust the water pressure at the sprinkler heads directly. You could even use an automated timing device to adjust the pressure and length of the cycle.
When performing sprinkler head adjustment, reposition the heads at proper aiming positions and make sure they are a correct distance from one another. You may have to measure the distance to be precise. You also have to make sure that no trees, shrubs or foliage is getting in the way of the spray. This will compromise the full effect of the system.
When looking into sprinkler head adjustment for pop up sprinklers (the most common type of system) you must manually pull the pop-up out of each head and then find the black tip on the end of the nozzle. Then, you can turn the tip in a counterclockwise fashion in order to increase the angle. You move it clockwise to reverse the angle back to its original position. If the adjustment requires more manual positioning, then you have to find the screw on the top of the nozzle and turn it counterclockwise or clockwise for the same effect.
Sprinkler head adjustment for a “rain bird” sprinkler is slightly different. This irrigation style sprinkler head system has several subsets and several spray head choices that can be adjusted for height, spread and pressure. This sprinkler head adjustment can be made by turning off the water, pinching the sprinkler head manually, and then twisting the outer plastic spray head to either the left or right. This will change the direction of the stream. You can also use a screwdriver to adjust the direction and pressure. The screw is located on the top of the spray head. You simply loosen the screw and then twist it.
http://www.greenmarkirrigation.com
Wednesday, November 10, 2010
Friday, October 15, 2010
Yard Sprinkler Systems?The Advantages of Hiring a Pro
Are you considering installing yard sprinkler systems? This is a wonderful way to keep your yard looking lush and beautiful. What is there to know about sprinklers before jumping into installation? The installation of a sprinkler system is all going to depend on what you want and what you are willing to do.
If you want a simple system installed and don’t mind a little manual labor, then installing a system on your own might just be the way to go for you personally. You will need to not only learn about installation but also such things as water pressure, connection size, the water source, the type of turf and the plants you will be watering.
If learning all of this, as well as the thought of spending a lot of time bending over and working in the summer heat doesn’t thrill you, you always have the option of paying an experienced worker to do the job for you. Having professionals install your yard sprinkler systems for you has other advantages, such as saving you time and giving you a higher quality of work.
A professional can help you in many ways such as in planning the layout of your system so that you are maximizing your watering abilities by not wasting money on beginner’s errors. (Like bad sprinkler head positioning) You certainly do not want your hard-earned money going to the watering of your driveway or sidewalk!
A pro can also help you to install an automatic sprinkler controller. Your life is busy, and you might not always remember to turn the sprinklers on. You probably won’t even notice your neglect of this duty until your lawn is brown and past the point of saving. An automatic control also gives you an advantage of turning off your yard sprinkler systems on a timed basis. The only thing worse than a dry brown lawn is a swamp where your lush lawn of grass use to be! That soggy mess will not only cost you pride, but it will also cost hefty price on your next water bill. A pro can help set you up with an automatic controller so both of these problems will be eliminated.
What happens when it rains? Another handy gadget to have a pro install is a rain sensor. There is no point in wasting precious water (let alone your precious money!) when the sky is providing you the service for free. When you install a rain sensor for your yard sprinkler systems, you won’t be that fool on the block everyone talks about who had his sprinklers running during an epic rain storm. What a waste!
Another popular doodad that a professional can give you advice on is a moisture sensor. This device monitors the actual amount of water your lawn and your plants are receiving. This helps you to maintain a healthy and lush front and back yard, but also makes sure you are not wasting water by over watering and then having large amounts of useless run off.
Expert advice and installation, as well as some good yard sprinkler systems devices, can make all the difference when it comes to keeping up lawn beauty.
Devin Gilliland Provides Expert opinions and reviews to help you Compare drip irrigation supplies and sprinklers.
If you want a simple system installed and don’t mind a little manual labor, then installing a system on your own might just be the way to go for you personally. You will need to not only learn about installation but also such things as water pressure, connection size, the water source, the type of turf and the plants you will be watering.
If learning all of this, as well as the thought of spending a lot of time bending over and working in the summer heat doesn’t thrill you, you always have the option of paying an experienced worker to do the job for you. Having professionals install your yard sprinkler systems for you has other advantages, such as saving you time and giving you a higher quality of work.
A professional can help you in many ways such as in planning the layout of your system so that you are maximizing your watering abilities by not wasting money on beginner’s errors. (Like bad sprinkler head positioning) You certainly do not want your hard-earned money going to the watering of your driveway or sidewalk!
A pro can also help you to install an automatic sprinkler controller. Your life is busy, and you might not always remember to turn the sprinklers on. You probably won’t even notice your neglect of this duty until your lawn is brown and past the point of saving. An automatic control also gives you an advantage of turning off your yard sprinkler systems on a timed basis. The only thing worse than a dry brown lawn is a swamp where your lush lawn of grass use to be! That soggy mess will not only cost you pride, but it will also cost hefty price on your next water bill. A pro can help set you up with an automatic controller so both of these problems will be eliminated.
What happens when it rains? Another handy gadget to have a pro install is a rain sensor. There is no point in wasting precious water (let alone your precious money!) when the sky is providing you the service for free. When you install a rain sensor for your yard sprinkler systems, you won’t be that fool on the block everyone talks about who had his sprinklers running during an epic rain storm. What a waste!
Another popular doodad that a professional can give you advice on is a moisture sensor. This device monitors the actual amount of water your lawn and your plants are receiving. This helps you to maintain a healthy and lush front and back yard, but also makes sure you are not wasting water by over watering and then having large amounts of useless run off.
Expert advice and installation, as well as some good yard sprinkler systems devices, can make all the difference when it comes to keeping up lawn beauty.
Devin Gilliland Provides Expert opinions and reviews to help you Compare drip irrigation supplies and sprinklers.
Saturday, October 9, 2010
Working With Sprinkler Valves?Helpful Hints
The purpose of having a yard sprinkler system is to make less work for you. It makes the task of keeping the lawn watered totally automated. When your sprinklers are working, they really do save you a lot of time. All you have to think about is how good your green grass is looking! However, what happens when something goes wrong? You will then have the tricky task of locating, cleaning, and fixing the sprinkler valves.
To locate these valves, your first step is to start back at the beginning. Find the main sprinkler system’s supply line. This waterline can sometimes be located in your house, and sometimes it may be located at its own separate pump and well that supplies the water for the system. Once you have found that main line, you just follow it until you get to the area where it splits and you see multiple waterlines. The sprinkler valves usually lie just beyond this split, and can be easy to locate. Sometimes, however, they can be buried underground.
If the valves are indeed buried underground, you can start by looking for green or black valve boxes in your yard. These are often located in flowerbeds or near the sprinkler controller so it may be best to start looking in those spots. If you cannot locate a box, you can contact your sprinkler installer, or even get out your old trusty metal detector to sweep the ground looking for the buried sprinkler valves.
Once you finally locate your valves it is time to get to work. Valves issues usually present in a few recognizable ways. They either get stuck, thus allowing the water to run non-stop until it is manually shut off; or, they end up doing the opposite and do not turn on at all, block any water flow. They can also simply “weepâ€, which is a small but never ending leak that can do some serious damage. If weeping is the case it might be time to call in a professional to fix your sprinkler valves.
s
If the valve is not turning on or is not shutting off then it is very likely that some debris has gotten lodged in it. You will need to take it apart carefully and clean each piece. Start by removing the solenoid (usually a black box with wires sticking out) and then check the plunger beneath it. It should move easily and be springy; if it is not, it may need to be replaced. Clean all parts of the valve thoroughly removing any bugs or dirt you see and then put it back together. If you have cleaned every part of the sprinkler valves and they are still not working properly, it may be a bad solenoid, bad wiring or even a ruined diaphragm. You can choose to read up on how to fix these matters yourself, or you can save yourself some time and call in the pros.
There are options you can try to fix sprinkler valves. With a little hard work, you can get your sprinklers back up and running again!
Richard Gilliland Provides Expert opinions and reviews to help you Compare irrigation supplies and Hunter Solar Sync.
To locate these valves, your first step is to start back at the beginning. Find the main sprinkler system’s supply line. This waterline can sometimes be located in your house, and sometimes it may be located at its own separate pump and well that supplies the water for the system. Once you have found that main line, you just follow it until you get to the area where it splits and you see multiple waterlines. The sprinkler valves usually lie just beyond this split, and can be easy to locate. Sometimes, however, they can be buried underground.
If the valves are indeed buried underground, you can start by looking for green or black valve boxes in your yard. These are often located in flowerbeds or near the sprinkler controller so it may be best to start looking in those spots. If you cannot locate a box, you can contact your sprinkler installer, or even get out your old trusty metal detector to sweep the ground looking for the buried sprinkler valves.
Once you finally locate your valves it is time to get to work. Valves issues usually present in a few recognizable ways. They either get stuck, thus allowing the water to run non-stop until it is manually shut off; or, they end up doing the opposite and do not turn on at all, block any water flow. They can also simply “weepâ€, which is a small but never ending leak that can do some serious damage. If weeping is the case it might be time to call in a professional to fix your sprinkler valves.
s
If the valve is not turning on or is not shutting off then it is very likely that some debris has gotten lodged in it. You will need to take it apart carefully and clean each piece. Start by removing the solenoid (usually a black box with wires sticking out) and then check the plunger beneath it. It should move easily and be springy; if it is not, it may need to be replaced. Clean all parts of the valve thoroughly removing any bugs or dirt you see and then put it back together. If you have cleaned every part of the sprinkler valves and they are still not working properly, it may be a bad solenoid, bad wiring or even a ruined diaphragm. You can choose to read up on how to fix these matters yourself, or you can save yourself some time and call in the pros.
There are options you can try to fix sprinkler valves. With a little hard work, you can get your sprinklers back up and running again!
Richard Gilliland Provides Expert opinions and reviews to help you Compare irrigation supplies and Hunter Solar Sync.
Tuesday, May 18, 2010
Thursday, April 29, 2010
Wednesday, April 21, 2010
Wednesday, April 7, 2010
Hunter Solar Sync
Hunter has recently released the newest in a long line of irrigation sensors called the Solar Sync, which most likely will change the way most people monitor watering their yards making rain and freeze sensors a thing of the past. Now most irrigation sensors just monitor rain fall and shut the irrigation system down for a period of time set by the user. Freeze sensors do basically the same thing and shut the irrigation system down when outside temperatures get to freezing levels but the Solar Sync sensor is in a league of its own as it monitors outside temperatures and uses that data to calculate the evapotranspiration know as (ET) and determines watering requirements for you.
As the outside temperatures drop or rise the Solar Sync will adjust your irrigation controller for you. If the outside weather has been extremely hot the Solar Sync will give the go ahead to the irrigation controller and water. If it’s extremely cold outside and in the danger zone for watering the Solar Sync will shut down the irrigation controller for you. This will save users all the time and aggravation of having to re-adjust the irrigation controller all the time and during the different seasons. The Hunter Solar Sync is now available and you should be able to find it at most online irrigation retailers if you can’t find it at your local Hunter dealer. Pricing is around $100.00 depending on where you get it and it is compatible with the New Hunter I-Core controller, Hunter Pro-C controller, PCC and ICC controllers as well.
Richard Gilliland Provides Expert opinions and reviews to help you Compare irrigation supplies and Hunter Solar Sync.
As the outside temperatures drop or rise the Solar Sync will adjust your irrigation controller for you. If the outside weather has been extremely hot the Solar Sync will give the go ahead to the irrigation controller and water. If it’s extremely cold outside and in the danger zone for watering the Solar Sync will shut down the irrigation controller for you. This will save users all the time and aggravation of having to re-adjust the irrigation controller all the time and during the different seasons. The Hunter Solar Sync is now available and you should be able to find it at most online irrigation retailers if you can’t find it at your local Hunter dealer. Pricing is around $100.00 depending on where you get it and it is compatible with the New Hunter I-Core controller, Hunter Pro-C controller, PCC and ICC controllers as well.
Richard Gilliland Provides Expert opinions and reviews to help you Compare irrigation supplies and Hunter Solar Sync.
Tuesday, April 6, 2010
The Most Important Irrigation Supplies
Due to stricter county and state irrigation restrictions if you are going to setup a new irrigation system you might want to move toward installing a water saving system.
Older irrigation systems just involved a irrigation timer, your average impact sprinklers and a water line. These systems which you most people already have installed at their home or business get the job done but seriously waste water. So what do you need to change or add in order to save water?
First get a rain or freeze sensor. These sensors will shut the irrigation controller off for a period of 24-72 hours after a rain, you can set it up per how much rain you want to trigger the shutoff. Rain bird has come out with a new wireless rain sensor called the wr2-rc. You can set this one up without having to run wires from your garage to the outside of your home or office. Hunter also makes a very good wireless sensor the WRC Sensor. Both of these sensors will get the job done.
Second add some drip irrigation to your plants and shrubs around your home or office. Rotors and spray sprinklers usually put off way too much water which can easily cause many plant diseases and fungus issues if you aren't careful. Drip irrigation is going to be the way of the future so upgrade your older heads.
Third get a new irrigation controller. There are tons of irrigation timers and controllers on the market these days but the newer ones such as the Hunter I-Core Controller have many water saving features built in for example detecting sprinkler head blow outs.
Devin Gilliland Provides Expert opinions and reviews to help you Compare irrigation supplies and sprinklers.
Older irrigation systems just involved a irrigation timer, your average impact sprinklers and a water line. These systems which you most people already have installed at their home or business get the job done but seriously waste water. So what do you need to change or add in order to save water?
First get a rain or freeze sensor. These sensors will shut the irrigation controller off for a period of 24-72 hours after a rain, you can set it up per how much rain you want to trigger the shutoff. Rain bird has come out with a new wireless rain sensor called the wr2-rc. You can set this one up without having to run wires from your garage to the outside of your home or office. Hunter also makes a very good wireless sensor the WRC Sensor. Both of these sensors will get the job done.
Second add some drip irrigation to your plants and shrubs around your home or office. Rotors and spray sprinklers usually put off way too much water which can easily cause many plant diseases and fungus issues if you aren't careful. Drip irrigation is going to be the way of the future so upgrade your older heads.
Third get a new irrigation controller. There are tons of irrigation timers and controllers on the market these days but the newer ones such as the Hunter I-Core Controller have many water saving features built in for example detecting sprinkler head blow outs.
Devin Gilliland Provides Expert opinions and reviews to help you Compare irrigation supplies and sprinklers.
Subscribe to:
Posts (Atom)